Wheel Bolt Pattern by Make and Model
300C ~ 300M ~ ASPEN ~ CIRRUS ~ CONCORDE ~ CONQUEST TSI ~ CORDOBA MIRADA FIFTH AVE ~ CROSSFIRE ~ LASER ~ LEBARON ~ LHS ~ NEW YORKER ~ PACIFICA ~ PROWLER ~ PT CRUISER ~ SEBRING ~ TOWN COUNTRY ~ TOWN COUNTRY VOYAGER ~ All CHRYSLER Model(s)
CHRYSLER Bolt Pattern(s):
CHRYSLER Wheel Size(s):
CHRYSLER Models / Bolt Pattern and Wheel Size Information:
2005 > CHRYSLER 300C
2005-08 CHRYSLER 300C RWD AWD SRTS
1998 > CHRYSLER 300M
1999-04 CHRYSLER 300M
2007-08 CHRYSLER ASPEN LIMITED 2WD 4WD
1995-00 CHRYSLER CIRRUS
1995-97 CHRYSLER CIRRUS
1993 > CHRYSLER CONCORDE, LXI
1993-04 CHRYSLER CONCORDE, LXI
1987-89 CHRYSLER CONQUEST TSI
2004 > CHRYSLER CROSSFIRE
2004-08 CHRYSLER CROSSFIRE
1984-85 CHRYSLER LASER
1990-94 CHRYSLER LASER
1986-89 CHRYSLER LASER, GTS
1981-85 CHRYSLER LEBARON
1985 > CHRYSLER LEBARON
1994 > CHRYSLER LHS
1994-01 CHRYSLER LHS
1981-85 CHRYSLER NEW YORKER
1985-93 CHRYSLER NEW YORKER
1994 > CHRYSLER NEW YORKER
2004 > CHRYSLER PACIFICA
2004-08 CHRYSLER PACIFICA
1997-02 CHRYSLER PROWLER
1996-07 CHRYSLER SEBRING CONVERTIBLE. JX
1995 > CHRYSLER SEBRING LXI
1996-06 CHRYSLER SEBRING LXI COUPE
2007-08 CHRYSLER SEBRING SEDAN
1986-96 CHRYSLER TOWN & COUNTRY VAN
Additional Wheel / Bolt Pattern Measurement Information
Key Identifying Wheel Dimensions: Wheel Bolt or Lug Pattern (or bolt circle, lug circle, lug pattern, etc.) is the measured diameter of an imaginary circle formed by the centers of the wheel lugs or bolt holes. Bolt patterns can be 3, 4, 5, 6, 7, 8 or 10 lug holes. A bolt circle of 5 x 4.5 would indicate a 5 lug bolt pattern on a circle with a diameter of 4.5 inches.
There are four important measurements that are used to categorize and identify a wheel for fitment purposes.
- Rim Diameter The actual diameter of the wheel at the point where the tire bead seats (NOT the outer lip of the rim).
- Rim Width Measure from the inside of the outer lip at the bead seating point to the inner lip.
- Back Spacing From the inside of the wheel at the point where it contacts the hub, brake drum or axle flange to the inside edge (lip) of the wheel.
- Bolt Pattern The measured diameter of an imaginary circle formed by the centers of the wheel lugs or bolt holes.
How To Measure Wheel Bolt Pattern
If there is an EVEN number of lugs: Measure center-to-center on lugs directly across from each other.
If there is an ODD number of lugs: Measure from the CENTER of one lug to the OUTER EDGE of the hole diagonally across from it.
Lug Nut Types
Bolt Pattern Torque Sequence / Specifications:
|Stud Size||Typical Torque Range in Ft/Lbs||Minimum Thread Engagement (turns)|
|12 x 1.5 mm||70 - 80||6.5|
|12 x 1.25 mm||70 - 80||8|
|14 x 1.5 mm||85 - 90||7.5|
|14 x 1.25 mm||85 - 90||9|
|7/16 in.||70 - 80||8|
|1/2 in.||75 - 85||8|
|9/16 in.||135 - 145||8|
Hub Center Bore
Hub Center Bore: Relates to the center hole in the wheel that centers the wheel on the hub of the car. Since most wheels are mass produced, they have a large center bore to accommodate several different vehicles. If this is the case, it is recommended that you use a hub ring. Hub rings are hard plastic or metal ring that fits between the wheel and the vehicle. This centers the wheel perfectly on the hub ensuring that there is no run out when the wheel is installed on to the vehicle. Without hub rings it is possible to get vibrations even if the wheel / tire assembly is perfectly balanced.
Wheel offset is the distance from the mounting surface of the wheel to the true center line of the rim. A positive offset means the mounting surface of the wheel is positioned in front of the true center line of the rim / tire assembly. This in effect brings the tire in to the fender well more. Conversely, a negative offset means the mounting surface of the wheel is behind the true center line of the rim / tire assembly. This will cause the tire to stick out away from the vehicle.
H = High - Positive Offset, typically FWD (Front Wheel Drive) +45, 40, 35 offsets
M = Medium - Neutral Offset, typically RWD (Rear Wheel Drive) +20 offset
L = Low - Zero to Negative Offset, Offset typically RWD (Rear Wheel Drive) 0 offset
Common Bolt Pattern Conversions
This information is accurate to the best of our knowledge. No warranties or guarantees are expressed or implied as to the accuracy of the information provided on this site. Use of this site constitutes your agreement to these terms.
- How to Measure Bolt Pattern Bolt pattern - diameter of an imaginary circle formed by the centers of the wheel lugs.
- Wheel Lug Nut / Bolt Torque Sequence Correct Wheel Lug Nut / Bolt Torque Sequence - 4 lug, 5 lug, 6 lug.
- How to Measure Wheel Back Spacing This measurement is important to be sure you have proper wheel clearance.
- How To Read A Tire Sidewall Learn to understand the common markings found on tire sidewalls.
- How To Plus Size Your Wheels
- Wheel, Tire and Fender Fitment Calculator Calculate Wheel Fitment, Tire Stretch and Rolling Radius. Includes Speedometer Error Calculator. Play with specs, try different settings and combinations, compare results.
- Tire Size Change / Speedometer Calibration Calculator This calculator is designed to give information related to tire size changes and the general impact they have on the calibration of a speedometer. It determines speedometer error and tire size information based on published and generally accepted tire dimensions as given by the standard US tire system (i.e. 205/45-ZR16). All calculations are based on the assumption of a new tire (as opposed to used) where the numbers on the tire accurately represent the dimensions.