4 X 137 Bolt Pattern Measurement and Specifications
The 4 X 137 Bolt Pattern or Pitch Circle Diameter (PCD) is made up of the stud count (4) and the bolt circle measurement (137), the notional circle determined by the center position of the studs.
How To Measure 4 Lug Bolt Patterns
Measure 4 lug wheel bolt patterns from center to center distance between two studs that are across the hub from each other. This measurement is your bolt pattern diameter. Learn more about wheel dimensions below.
What Vehicles Use Wheels With 4 X 137 Bolt Pattern?
The 4 X 137 bolt pattern is common to KAWASAKI, CAN-AM BOMBARDIER and SUZUKI vehicles. A full list of vehicle makes and models appears below.
Bolt Pattern Torque Sequence / Specifications:
4 X 137 Bolt Pattern Torque Sequence Specifications: 1, 3, 2, 4
|Stud Size||Typical Torque Range in Ft/Lbs||Minimum Thread Engagement (turns)|
|12 x 1.5 mm||70 - 80||6.5|
|12 x 1.25 mm||70 - 80||8|
|14 x 1.5 mm||85 - 90||7.5|
|14 x 1.25 mm||85 - 90||9|
|7/16 in.||70 - 80||8|
|1/2 in.||75 - 85||8|
|9/16 in.||135 - 145||8|
It is prudent to re-torque wheels after about 60 to 90 miles (100km to 150km) of driving. Learn more about lug nuts and torque.
Hub Center Bore
Hub Center Bore: Relates to the center hole in the wheel that centers the wheel on the hub of the car. Since most wheels are mass produced, they have a large center bore to accommodate several different vehicles. If this is the case, it is recommended that you use a hub ring. Hub rings are hard plastic or metal ring that fits between the wheel and the vehicle. This centers the wheel perfectly on the hub ensuring that there is no run out when the wheel is installed on to the vehicle. Without hub rings it is possible to get vibrations even if the wheel / tire assembly is perfectly balanced.
Wheel offset is the distance from the mounting surface of the wheel to the true center line of the rim. A positive offset means the mounting surface of the wheel is positioned in front of the true center line of the rim / tire assembly. This in effect brings the tire in to the fender well more. Conversely, a negative offset means the mounting surface of the wheel is behind the true center line of the rim / tire assembly. This will cause the tire to stick out away from the vehicle.
H = High - Positive Offset, typically FWD (Front Wheel Drive) +45, 40, 35 offsets
M = Medium - Neutral Offset, typically RWD (Rear Wheel Drive) +20 offset
L = Low - Zero to Negative Offset, Offset typically RWD (Rear Wheel Drive) 0 offset
Wheels, Spacers and Adapters
Wheel Bolt Pattern by Make and Model
Comparing to CAN-AM BOMBARDIER 800 OUTLANDER HO EFI/XT Center Bore: 0
Vehicle Make(s) with 4 X 137 Bolt Pattern:
2003-05 CAN-AM BOMBARDIER 400 H.O. 4X4
2007-09 CAN-AM BOMBARDIER 800 RENEGADE
1993, 1995 KAWASAKI KAF300B MULE 500
1997-01, 2003-04 KAWASAKI KAF300C MULE 550
2005-08 KAWASAKI KAF400B MULE 600
1993, 95, 97-00 KAWASAKI KAF620A MULE 2510 4X4
1994-95, 97-00 KAWASAKI KAF620C MULE 2500
2001-08 KAWASAKI KAF620E/H MULE 3010 4X4
2001-08 KAWASAKI KAF620G MULE 3000
1988-99 KAWASAKI KLF220 BAYOU
2000-02 KAWASAKI KLF220 BAYOU
2003-09 KAWASAKI KLF250 BAYOU
1986-87 KAWASAKI KLF300A BAYOU
1989-99 KAWASAKI KLF300B BAYOU
2000-04 KAWASAKI KLF300B BAYOU 2X4
1989-99 KAWASAKI KLF300C BAYOU 4X4
2000-04 KAWASAKI KLF300C BAYOU 4X4
1993-99 KAWASAKI KLF400B BAYOU 4X4
2008-09 KAWASAKI KRF750A-F TERYX 750 4X4
2000-02 KAWASAKI KVF300A PRAIRIE 4X4
2000-02 KAWASAKI KVF300B PRAIRIE 2X4
2003-09 KAWASAKI KVF360B PRAIRIE 2X4/4X4
1997-98 KAWASAKI KVF400A PRAIRIE 4X4
2000-02 KAWASAKI KVF400D PRAIRIE 2X4
2002-03 KAWASAKI KVF650A/B PRAIRIE 4X4
2004-06 KAWASAKI KVF700A/B/D PRAIRIE 4X4
2004-05 SUZUKI LTV700F TWIN PEAKS 4X4
Additional Wheel / Measurement Information
Key Identifying Wheel Dimensions: Wheel Bolt or Lug Pattern (or bolt circle, lug circle, lug pattern, etc.) is the measured diameter of an imaginary circle formed by the centers of the wheel lugs or bolt holes. Bolt patterns can be 3, 4, 5, 6, 7, 8 or 10 lug holes. A bolt circle of 5 x 4.5 would indicate a 5 lug bolt pattern on a circle with a diameter of 4.5 inches.
There are four important measurements that are used to categorize and identify a wheel for fitment purposes.
- Rim Diameter The actual diameter of the wheel at the point where the tire bead seats (NOT the outer lip of the rim).
- Rim Width Measure from the inside of the outer lip at the bead seating point to the inner lip.
- Back Spacing From the inside of the wheel at the point where it contacts the hub, brake drum or axle flange to the inside edge (lip) of the wheel.
- Bolt Pattern The measured diameter of an imaginary circle formed by the centers of the wheel lugs or bolt holes.
How To Measure Wheel Bolt Pattern
If there is an EVEN number of lugs: Measure center-to-center on lugs directly across from each other.
If there is an ODD number of lugs: Measure from the CENTER of one lug to the OUTER EDGE of the hole diagonally across from it.
Lug Nut Types
Common Bolt Pattern Conversions
This information is accurate to the best of our knowledge. No warranties or guarantees are expressed or implied as to the accuracy of the information provided on this site. Use of this site constitutes your agreement to these terms.
- How to Measure Bolt Pattern Bolt pattern - diameter of an imaginary circle formed by the centers of the wheel lugs.
- Wheel Lug Nut / Bolt Torque Sequence Correct Wheel Lug Nut / Bolt Torque Sequence - 4 lug, 5 lug, 6 lug.
- How to Measure Wheel Back Spacing This measurement is important to be sure you have proper wheel clearance.
- How To Read A Tire Sidewall Learn to understand the common markings found on tire sidewalls.
- How To Plus Size Your Wheels
- Wheel, Tire and Fender Fitment Calculator Calculate Wheel Fitment, Tire Stretch and Rolling Radius. Includes Speedometer Error Calculator. Play with specs, try different settings and combinations, compare results.
- Tire Size Change / Speedometer Calibration Calculator This calculator is designed to give information related to tire size changes and the general impact they have on the calibration of a speedometer. It determines speedometer error and tire size information based on published and generally accepted tire dimensions as given by the standard US tire system (i.e. 205/45-ZR16). All calculations are based on the assumption of a new tire (as opposed to used) where the numbers on the tire accurately represent the dimensions.