6 X 5.5 Bolt Pattern Measurement and Specifications
The 6 X 5.5 Bolt Pattern or Pitch Circle Diameter (PCD) is made up of the stud count (6) and the bolt circle measurement (5.5), the notional circle determined by the center position of the studs.
How To Measure 6 Lug Bolt Patterns
Measure 6 lug wheel bolt patterns from center to center distance between two studs that are across the hub from each other. This measurement is your bolt pattern diameter. Learn more about wheel dimensions below.
What Vehicles Use Wheels With 6 X 5.5 Bolt Pattern?
The 6 X 5.5 bolt pattern is common to TOYOTA, NISSAN, ISUZU, MITSUBISHI, MAZDA, INFINITI, LEXUS, DODGE, HONDA, JEEP, CADILLAC, ACURA and other vehicles. A full list of vehicle makes and models appears below.
Wheels with 6 X 5.5 bolt pattern are sometimes found on commercial trailers and heavy-duty utility trailers. More about trailer wheels...
Bolt Pattern Torque Sequence / Specifications:
6 X 5.5 Bolt Pattern Torque Sequence Specifications: 1, 6, 4, 2, 5, 3
|Stud Size||Typical Torque Range in Ft/Lbs||Minimum Thread Engagement (turns)|
|12 x 1.5 mm||70 - 80||6.5|
|12 x 1.25 mm||70 - 80||8|
|14 x 1.5 mm||85 - 90||7.5|
|14 x 1.25 mm||85 - 90||9|
|7/16 in.||70 - 80||8|
|1/2 in.||75 - 85||8|
|9/16 in.||135 - 145||8|
It is prudent to re-torque wheels after about 60 to 90 miles (100km to 150km) of driving. Learn more about lug nuts and torque.
Hub Center Bore
Hub Center Bore: Relates to the center hole in the wheel that centers the wheel on the hub of the car. Since most wheels are mass produced, they have a large center bore to accommodate several different vehicles. If this is the case, it is recommended that you use a hub ring. Hub rings are hard plastic or metal ring that fits between the wheel and the vehicle. This centers the wheel perfectly on the hub ensuring that there is no run out when the wheel is installed on to the vehicle. Without hub rings it is possible to get vibrations even if the wheel / tire assembly is perfectly balanced.
Wheel offset is the distance from the mounting surface of the wheel to the true center line of the rim. A positive offset means the mounting surface of the wheel is positioned in front of the true center line of the rim / tire assembly. This in effect brings the tire in to the fender well more. Conversely, a negative offset means the mounting surface of the wheel is behind the true center line of the rim / tire assembly. This will cause the tire to stick out away from the vehicle.
H = High - Positive Offset, typically FWD (Front Wheel Drive) +45, 40, 35 offsets
M = Medium - Neutral Offset, typically RWD (Rear Wheel Drive) +20 offset
L = Low - Zero to Negative Offset, Offset typically RWD (Rear Wheel Drive) 0 offset
Wheels, Spacers and Adapters
Wheel Bolt Pattern by Make and Model
Comparing to CHEVROLET/GMC TAHOE/ YUKON Center Bore: 78.3 ~ Offset: L
Vehicle Make(s) with 6 X 5.5 Bolt Pattern:
1996-99 ACURA SLX
1998 > CADILLAC ESCALADE, EXT & ESV
1998-'08 CADILLAC ESCALADE, EXT & ESV
1993 > CHEVROLET/GMC ASTRO/SAFARI
2003-05 CHEVROLET/GMC ASTRO/SAFARI
2002 > CHEVROLET/GMC AVALANCHE
1992 > CHEVROLET/GMC TAHOE/ YUKON
1986-89 DODGE RAIDER 4WD
1977-84 FORD COURIER PICKUP
1994-02 HONDA PASSPORT
1994-03 HONDA PASSPORT
2007-08 HYUNDAI ENTOURAGE
1996 > INFINITI QX4
1996-03 INFINITI QX4
1989-00 ISUZU AMIGO
2002 > ISUZU AXIOM
2002-041 ISUZU AXIOM
1980-96 ISUZU PICKUP
1991 > ISUZU RODEO, RODEO SPORT
1991-04 ISUZU RODEO, RODEO SPORT
1992-03 ISUZU TROOPER
1992-96 ISUZU TROOPER
1984-91 ISUZU TROOPER II
1999 > ISUZU VEHICROSS
2006-08 KIA SEDONA LX, EX
2003 > LEXUS GX 470
2003-08 LEXUS GX 470
1996-97 LEXUS LX 450
1977-93 MAZDA 2600 PICKUP
1977-93 MAZDA B-2000, 2200, 2300
1977-93 MAZDA SE-5 OPT.15
1983-00 MITSUBISHI MONTERO
1992-06 MITSUBISHI MONTERO
1992 > MITSUBISHI MONTERO SPORT
1992-04 MITSUBISHI MONTERO SPORT
1983-96 MITSUBISHI PICKUP
1987-96 NISSAN 2WD PICKUP FRONTIER
1987-96 NISSAN 4WD PICKUP FRONTIER
1998 > NISSAN FRONTIER
1987-04 NISSAN PATHFINDER
1987-04 NISSAN PATHFINDER 2WD & 4WD
2004 > NISSAN PATHFINDER ARMADA
1973-86 NISSAN PICKUP
1973-86 NISSAN PICKUP 2WD/4WD
2000 > NISSAN XTERRA
2000-04 NISSAN XTERRA 2WD, 4WD
1986-02 TOYOTA 4-RUNNER
2000 > TOYOTA 4-RUNNER
2003 > TOYOTA 4-RUNNER V-6 & V-8
2003-08 TOYOTA 4-RUNNER V-6 & V-8
2007-08 TOYOTA FJ CRUISER
1969-92 TOYOTA LANDCRUISER
1993-97 TOYOTA LANDCRUISER
1980-95 TOYOTA PICKUP 4WD, 4 RUNNER
2001 > TOYOTA SEQUOIA
2001-07 TOYOTA SEQUOIA 2WD, 4WD
1993-96 TOYOTA T-100
2005-08 TOYOTA TACOMA 2WD, W, OE 16"
1999 > TOYOTA TUNDRA
1999-06 TOYOTA TUNDRA 2WD, 4WD
Additional Wheel / Measurement Information
Key Identifying Wheel Dimensions: Wheel Bolt or Lug Pattern (or bolt circle, lug circle, lug pattern, etc.) is the measured diameter of an imaginary circle formed by the centers of the wheel lugs or bolt holes. Bolt patterns can be 3, 4, 5, 6, 7, 8 or 10 lug holes. A bolt circle of 5 x 4.5 would indicate a 5 lug bolt pattern on a circle with a diameter of 4.5 inches.
There are four important measurements that are used to categorize and identify a wheel for fitment purposes.
- Rim Diameter The actual diameter of the wheel at the point where the tire bead seats (NOT the outer lip of the rim).
- Rim Width Measure from the inside of the outer lip at the bead seating point to the inner lip.
- Back Spacing From the inside of the wheel at the point where it contacts the hub, brake drum or axle flange to the inside edge (lip) of the wheel.
- Bolt Pattern The measured diameter of an imaginary circle formed by the centers of the wheel lugs or bolt holes.
How To Measure Wheel Bolt Pattern
If there is an EVEN number of lugs: Measure center-to-center on lugs directly across from each other.
If there is an ODD number of lugs: Measure from the CENTER of one lug to the OUTER EDGE of the hole diagonally across from it.
Lug Nut Types
Common Bolt Pattern Conversions
This information is accurate to the best of our knowledge. No warranties or guarantees are expressed or implied as to the accuracy of the information provided on this site. Use of this site constitutes your agreement to these terms.
- How to Measure Bolt Pattern Bolt pattern - diameter of an imaginary circle formed by the centers of the wheel lugs.
- Wheel Lug Nut / Bolt Torque Sequence Correct Wheel Lug Nut / Bolt Torque Sequence - 4 lug, 5 lug, 6 lug.
- How to Measure Wheel Back Spacing This measurement is important to be sure you have proper wheel clearance.
- How To Read A Tire Sidewall Learn to understand the common markings found on tire sidewalls.
- How To Plus Size Your Wheels
- Wheel, Tire and Fender Fitment Calculator Calculate Wheel Fitment, Tire Stretch and Rolling Radius. Includes Speedometer Error Calculator. Play with specs, try different settings and combinations, compare results.
- Tire Size Change / Speedometer Calibration Calculator This calculator is designed to give information related to tire size changes and the general impact they have on the calibration of a speedometer. It determines speedometer error and tire size information based on published and generally accepted tire dimensions as given by the standard US tire system (i.e. 205/45-ZR16). All calculations are based on the assumption of a new tire (as opposed to used) where the numbers on the tire accurately represent the dimensions.